Heath Zenith SL-5679 Instrukcja Użytkownika Pobierz pdf

Gasket

(Optional)

Mounting

Bracket

Photocontrol

Ground

Screw

Fixture

Lamp

Temporary

Installation Instructions

READ ALL INSTRUCTIONS CAREFULLY BEFORE BEGINNING INSTALLATION.

NOTE: All wiring must be run in accordance with the National Electrical Code (Canadian Electrical Code in Canada) through conduit or

another acceptable means. Contact a qualiﬁed electrician if there is any question as to the suitability of the system.

This ﬁxture can be mounted on a wall with, or without using a ﬂush-mounted

junction box. Do not attempt to mount this ﬁxture on a surface-mounted

“Wet Location” junction box. Use the instructions below that apply to

your application.

Installation Using A Junction Box

Note: If your junction box protrudes out of the wall slightly, you may want

to use the enclosed gasket so less caulking is required.

1. Hold the Mounting Bracket and Gasket over the junction box. Thread

the supply wires through the large hole in the back of the Mounting

bracket. Select the holes in the mounting bracket that line up with the

screw holes in the junction box. Make sure the bottom of the Mounting

Bracket is level. Secure with the two #8 screws provided.

Installation Without A Junction Box

1. Select a location on a ﬂat wall with structurally sound wood and from 5

to 25 feet from the ground. The wood should be at least one inch thick

to safely secure the ﬁxture.

2. Use the Mounting Bracket as a template. Hold it at the desired mount-

ing location (making sure the bottom is level), and mark four mounting

holes.

3. Use four #8 or #10 wood screws or galvanized deck screws at least 1

inch long (not provided) to secure the Mounting Bracket to the wall. It

may be necessary to drill appropriate pilot holes if mounted to hardwood

to avoid splitting.

4. Remove the knockout in the bottom of the Mounting Bracket, and bring

your supply wires through this knockout using appropriate ﬂexible

conduit or other approved means of wiring.

Complete The Installation

1. Put the Temporary Pin through the holes in the Mounting Bracket.

2. This ﬁxture must be grounded. Connect the supply ground wire to the

green ground screw. You can also attach a bare or green “pigtail” to

the green ground screw, then connect the ground pigtail to the supply

ground when the other supply wires are connected.

3. Slide the ﬁxture onto the Mounting Bracket, and allow the ﬁxture to

rest on the Temporary Pin.

4. Connect the ﬁxture wires to the supply wires (

black to black, white to

white, and if a ground pigtail was added above, connect this pigtail to

the supply ground wire). Secure with the wire connectors provided.

5. Remove the Temporary Pin, and slide the ﬁxture all the way down onto

the Mounting Bracket making sure no wires get pinched.

6. Install the screw through the bottom of the Mounting Bracket and into

the ﬁxture housing. Tighten this screw.

7. Install

ONLY a 70 watt high pressure sodium type S62 lamp (pro-

vided).

8. Caulk ﬁxture mounting surface with silicone weather sealant.

To test operation during daylight, cover the photocontrol with black tape.

Turn on the power. The light will take up to ten minutes to reach full bright-

ness. Remove the tape from the photocontrol and your unit will operate

automatically—on at dusk, off at dawn.

Dusk-To-Dawn

Patio Light

Model SL-5679

WARNING: Turn power off at the fuse or circuit

breaker.

Lamp in Fixture Contains Mercury. Dispose According

to Local, State, or Federal Laws.

1 2 3 4 5 6 7 8

Podsumowanie treści

Strona 1 - Model SL-5679

Strona 2 - Ignitor

2598-1235-01Lamp Socket Photocell Socket Ballast Ignitor Red Red Red Black Black Blue Blue White White White Black White Black 120V ACInputBallast As

Strona 3 - Luz de patio del crepúsculo

Strona 4 - Estabilizador

4598-1235-011. Retire la cobertura plástica.2. Retire la bombilla.3. Retire los cinco tornillos que sujetan el reﬂector a la caja del artefacto.4.

Strona 5 - Mode d’installation

Strona 6 - Igniteur

6598-1235-011. Retirez le couvercle de plastique.2. Retirez l’ampoule.3. Retirez les 5 vis qui ﬁxent le réﬂecteur au boîtier du luminaire.4. Étiqu

Strona 7 - Service Technique

7598-1235-01Technical ServicePlease call 1-800-858-8501 (English speaking only) for assistance before returning product to store.If you experience a p

Strona 8 - GARANTIE LIMITÉE DE 2 ANS

8598-1235-01TWO YEAR LIMITED WARRANTYThis is a “Limited Warranty” which gives you speciﬁc legal rights. You may also have other rights which vary from

Komentarze do niniejszej Instrukcji

Brak uwag

Heath Zenith SL-5679 Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Nie Heath Zenith SL-5679. Heath Zenith SL-5679 User's Manual Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Nie Heath Zenith SL-5679